bmw e90 brake pad sensor reset

BMW E90 Brake Pad Sensor Reset: DIY Guide & SEO

By David Allen
AD

If you're a proud owner of a BMW E90 and recently encountered a dash warning light indicating a potential issue with your brake pad sensor, you're not alone. This issue is quite common among E90 models due to the sensors' susceptibility to wear and tear over time. The good news is, you can reset the brake pad sensor yourself, saving you a trip to the mechanic and some cash in the process. Let's dive into the step-by-step guide on how to reset the brake pad sensor on your BMW E90.

Before we begin, it's crucial to understand that this procedure involves safety checks and requires basic mechanical knowledge. Always prioritize safety first and foremost. If you're unsure about any step, consult a professional. Now, let's get started.

Preparation and Safety Checks

Ensuring your safety and the vehicle's stability is the first step. Here's what you need to do:

AD
HOW TO BYPASS BRAKE SENSOR demonstrated on BMW
HOW TO BYPASS BRAKE SENSOR demonstrated on BMW
the front brake and disc of a car
the front brake and disc of a car
⚡️ BMW 5 Series brake pad reset, oil reset, and service reset.
⚡️ BMW 5 Series brake pad reset, oil reset, and service reset.
  1. Park your BMW E90 on a flat surface and engage the parking brake.
  2. Place wheel chocks behind the rear wheels to prevent rolling.
  3. Remove the wheels using a lug wrench. You may need to loosen the lug nuts before jacking up the vehicle.

Locating the Sensor

Now that your BMW E90 is securely lifted and the wheels are off, it's time to locate the brake pad sensor. Here's where to find it:

  • The sensor is typically found in the caliper assembly, on the outer pad.
  • Check both front wheels; you'll need to locate and reset the sensor on both sides.

Disconnecting and Resetting the Sensor

With the sensor located, here's how to proceed with the reset:

⚡️how to reset brake pad light on BMW
⚡️how to reset brake pad light on BMW
BMW No Crank No Start? Fix IBS Sensor Fault
BMW No Crank No Start? Fix IBS Sensor Fault
Schéma de fusibles et relais pour BMW Série 3 (E90 / E91 / E92 / E93; 2005-2013) - schémas de boîtes à fusibles
Schéma de fusibles et relais pour BMW Série 3 (E90 / E91 / E92 / E93; 2005-2013) - schémas de boîtes à fusibles
  1. Carefully remove the plastic cover protecting the sensor using a flathead screwdriver or a pick tool.
  2. Once the cover is off, you'll notice two wires connected to the sensor. Carefully disconnect them.
  3. Now, comes the reset part. To reset the brake pad sensor, simply reconnect the wires and then promptly disconnect them again. Yes, you read that right. The simple act of reconnecting and disconnecting the wires resets the sensor.
  4. Reconnect the wires and replace the protective cover.

Reassembling and Testing

With the brake pad sensor reset, it's time to put everything back together and test your work.

Start by reinstalling the wheel, ensuring it's properly secured with the lug nuts before lowering the car. Once the vehicle is back on the ground, tighten the lug nuts fully using a wrench.

AD

Testing the Reset

Now comes the crucial part: testing the reset. Here's how:

a person is plugging in to the power cord on a car's engine
a person is plugging in to the power cord on a car's engine
an image of a car dashboard with the words reset bmw e90 service light
an image of a car dashboard with the words reset bmw e90 service light
How to activate BMW e90 shift indicator
How to activate BMW e90 shift indicator
BMW
BMW
Fuse box diagram BMW 3 2007 - 2013 E90 E91 relay with assignment and location
Fuse box diagram BMW 3 2007 - 2013 E90 E91 relay with assignment and location
  1. Start your BMW E90 and observe the dash warning light.
  2. If the light remains on, it's likely that the sensor was reset incorrectly, or there's a more severe issue at hand. In this case, consult a professional mechanic.
  3. If the light turns off, congratulations! You've successfully reset the brake pad sensor on your BMW E90.

However, it's essential to keep an eye on the warning light over the next few days. If it reappears, it might indicate a persistent issue with the brake pad sensor or the brake system itself.

Regular maintenance and safety checks are crucial for keeping your BMW E90 in optimal condition. Brake pad sensors, like many other components, are subject to wear and tear. So, it's a good idea to periodically check their functionality and perform the reset if necessary. Happy driving!

AD
AD